attiny2313A-SU unable to load

[Akskaypohankar]

hi its been few days I have been trying to upload a code to attiny2313A-SU using Arduino Nano as ISP programmer
i have checked hardware connections 10 times and changed iC 3 times but no luck
hear is the full response from Arduino

avrdude: Version 6.3-20201216
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch

     System wide configuration file is "C:\Users\Akshay\Documents\ArduinoData\packages\ATTinyCore\hardware\avr\1.5.2/avrdude.conf"

     Using Port                    : COM7
     Using Programmer              : stk500v1
     Overriding Baud Rate          : 19200
     Setting bit clk period        : 5.0
     AVR Part                      : ATtiny4313
     Chip Erase delay              : 15000 us
     PAGEL                         : PD4
     BS2                           : PD6
     RESET disposition             : possible i/o
     RETRY pulse                   : SCK
     serial program mode           : yes
     parallel program mode         : yes
     Timeout                       : 200
     StabDelay                     : 100
     CmdexeDelay                   : 25
     SyncLoops                     : 32
     ByteDelay                     : 0
     PollIndex                     : 3
     PollValue                     : 0x53
     Memory Detail                 :

                              Block Poll               Page                       Polled
       Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
       ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
       eeprom        65     6     4    0 no        256    4      0  4000  4500 0xff 0xff
       flash         65     6    64    0 yes      4096   64     64  4500  4500 0xff 0xff
       signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00
       lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
       lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
       hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
       efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
       calibration    0     0     0    0 no          2    0      0     0     0 0x00 0x00

     Programmer Type : STK500
     Description     : Atmel STK500 Version 1.x firmware
     Hardware Version: 2
     Firmware Version: 1.18
     Topcard         : Unknown
     Vtarget         : 0.0 V
     Varef           : 0.0 V
     Oscillator      : Off
     SCK period      : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x000000 (retrying)

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x000000 (retrying)

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x000000
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.

avrdude done. Thank you.

An error occurred while uploading the sketch

please help me on this .

[Akskaypohankar]

sorry i posted wrong response in previous post

hear is the correct one

avrdude: Version 6.3-20201216
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch

     System wide configuration file is "C:\Users\Akshay\Documents\ArduinoData\packages\ATTinyCore\hardware\avr\1.5.2/avrdude.conf"

     Using Port                    : COM7
     Using Programmer              : stk500v1
     Overriding Baud Rate          : 19200
     Setting bit clk period        : 5.0
     AVR Part                      : ATtiny2313a
     Chip Erase delay              : 15000 us
     PAGEL                         : PD4
     BS2                           : PD6
     RESET disposition             : possible i/o
     RETRY pulse                   : SCK
     serial program mode           : yes
     parallel program mode         : yes
     Timeout                       : 200
     StabDelay                     : 100
     CmdexeDelay                   : 25
     SyncLoops                     : 32
     ByteDelay                     : 0
     PollIndex                     : 3
     PollValue                     : 0x53
     Memory Detail                 :

                              Block Poll               Page                       Polled
       Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
       ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
       eeprom        65     6     4    0 no        256    4      0  4000  4500 0xff 0xff
       flash         65     6    64    0 yes      2048   32     64  4500  4500 0xff 0xff
       signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00
       lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
       lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
       hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
       efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
       calibration    0     0     0    0 no          2    0      0     0     0 0x00 0x00

     Programmer Type : STK500
     Description     : Atmel STK500 Version 1.x firmware
     Hardware Version: 2
     Firmware Version: 1.18
     Topcard         : Unknown
     Vtarget         : 0.0 V
     Varef           : 0.0 V
     Oscillator      : Off
     SCK period      : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x000000 (retrying)

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x000000 (retrying)

Reading | An error occurred while uploading the sketch
################################################## | 100% 0.02s

avrdude: Device signature = 0x000000
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.

avrdude done. Thank you.

[hmeijdam]

A picture of your hardware setup may help. e.g. is it a standalone breadboard setup or do you have other passive components connected to any of the programming pins?

[SpenceKonde]

Wiring problem or part set to use a crystal that is not present or not functioning, clock must be provided in such cases in order to revive those.